Industrial Components
12x12x8mm Tactile Push Button 40xx
Relay DC 5V 7A
Resistor Network (A103J)
RC522 RFID Module with Tag and card
SG90 Servo Motor
BD139 NPN Bipolar Medium Power Transistor (BJ...
Ultrasonic Sensor Module HCSR04
DHT11 Temperature and Humidity Sensor
Soil Moisture Sensor Module
RGB LED Common Anode 4 Pin (5mm)
Mini Breadboard 170 Points
2 Pin Screw Type PCB Terminal Block 126-5.0 (...
Jumper Wire (Female to Female)
Jumper Wire (Male to Female)
Jumper Wire (Male to Male)
6 Pin JST Connector Male - 2.54mm Pitch (Pack...
- Sale -17%
12x12x8mm Tactile Push Button 40xx
it's a 12x12x8mm Tactile Push Button 40xx package. The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. Features Up to 1 Million operations Actuation force of 1.6N to 2.5N Small...
- Sale -9%
Relay DC 5V 7A
SPDT(Single Pole Double Throw) relay is used as a switch for high current AC/DC appliances which need to be controlled from a microcontroller or sensor output. 5V PCB Mount Sugar Cube SPDT Relay instead of...
- Sale -17%
Resistor Network (A103J)
It's a A103J resistor network. This resistor network consists Maximum short time overload and Minimum insulation resistance. This is 10k ohm resistor network array with 1/8w and it have p through hole pin. Specification Value 10 kΩ...
- Sale -15%
RC522 RFID Module with Tag and card
RFID Reader / Writer 13.56MHz with Cards RC522 A 13.56MHz RF reader cum writer module with an RC522 IC and two S50 RFID cards are included in the kit. The MF RC522 is a highly...
- Sale -14%
SG90 Servo Motor
It's a SG90 servo motor. This servo motor generally Used as actuators in many robots like Biped Robot, Hexapod, robotic arm etc. It's Commonly used for steering system in RC toys. This servo motor generally use in...
- Sale -9%
BD139 NPN Bipolar Medium Power Transistor (BJT) 80V 1.5A TO-126 Package
The BD139 is a NPN complementary low voltage NPN transistor in 3 pin Its package is TO-126. This device is designed for audio amplifiers and drivers utilizing complementary or quasi-complementary circuits. Specification Type Medium Power NPN...
- Sale -16%
Ultrasonic Sensor Module HCSR04
This module operates on 5 V DC voltage and 15 mA current. The operating frequency for the sensor is 40 Hz. The minimum range of the module is 2 CM while its maximum range is...
- Sale -17%
DHT11 Temperature and Humidity Sensor
DHT11 sensor is a digital signal output component used to sense temperature and humidity of the surroundings. This module operates at 3.5 to 5.5V DC. Operating current of the module is 0.3mA when it is...
- Sale -17%
Soil Moisture Sensor Module
Soil Moisture Sensor Module can be used to detect the moisture of the soil or judge if there is water around the sensor. It has both analog and digital outputs. We can vary the digital output...
- Sale -17%
RGB LED Common Anode 4 Pin (5mm)
It's a RGB LED Common Anode 4 Pin. This is a semiconductor device and it is used as a indicator lamp in many device and are increasingly used for another lighting. They are used in wide...
- Sale -11%
Mini Breadboard 170 Points
It's a Mini Breadboard 170 Points. This is one type of bread board which is made from plastic and it is generally used for DIY project . Specification Dimensions: 47x35x8. 2.54 mm hole spacing. ABS plastic...
- Sale -9%
2 Pin Screw Type PCB Terminal Block 126-5.0 (5mm Pitch)
It's a 2 Pin Screw Type PCB Terminal Block 126-5.0 (5mm Pitch). This PCB CONNECTORS can handle AC 300V 10A. The 2 Pin 5mm pitch Pluggable type PCB terminal block is a type of electronic component...
- Sale -11%
Jumper Wire (Female to Female)
These are female to female jumper wires used in connecting the female header pin of Arduino or any development board to plug in any other development board. They are simple wires that have connector pins...
- Sale -7%
Jumper Wire (Male to Female)
These are male to female jumper wires used in connecting the female header pin of any development board to other development boards having a male connector. They are simple wires that have connector pins at...
- Sale -6%
Jumper Wire (Male to Male)
These are male to male jumper wires used in connecting the male header pin of any development board to other development boards having a male connector. They are simple wires that have connector pins at...
- Sale -13%
6 Pin JST Connector Male - 2.54mm Pitch (Pack of 20)
It's a 6 Pin JST Connector Male - 2.54mm Pitch. This connector serves a variety of functions, including providing AC power to PCs and lab equipment, connecting CCTV cameras and other electronic devices, operating various forms of...
