
New Products
2 Channel 5V 10A Relay Module with optocoupler
VTR Push Button Locking
Dual Shaft BO Motor Straight 150 RPM
SimonK 30A BLDC ESC Electronic Speed Controll...
Attiny85 Micro-USB module
TTP226 - 8 Channel Capacitive Touch Sensor Mo...
LM2596 DC-DC Buck Converter Adjustable Step D...
1k ohm SMD Resistor 1206 (Pack of 100)
330 ohm SMD Resistor 1206 (Reel of 5000)
Wheel for BO Motor 70mm x 8mm
LM35 Temperature sensor
BD140 PNP Bipolar Medium Power Transistor (BJ...
0.1uF SMD Capacitor 1206 (pack of 100)
XL6009 DC- DC Adjustable Step UP Boost Power ...
L293D Motor Shield for Arduino
28BYJ-48 5V Mini Stepper Motor
2 Channel 5V 10A Relay Module with optocoupler
5V 2-Channel Relay interface board, Be able to control various appliances and other equipment with large current. It can be controlled directly by Micro-controller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic). Features ...
VTR Push Button Locking
It's a 25v 2A VTR Push Button. This is a VTR Push Button with a self-locking design and a 6-pin. rectangle button. The pins are normally open (disconnected) and closed when the button is pressed...
Dual Shaft BO Motor Straight 150 RPM
The 150 RPM Dual Shaft BO Motor Plastic Gear Motor BO series straight motor gives good torque and rpm at lower operating voltages. It is a low-cost geared DC Motor which is an alternative to metal...
SimonK 30A BLDC ESC Electronic Speed Controller with Connectors
It's a SimonK 30A BLDC ESC Electronic Speed Controller with Connectors. This speed controller generally used for BLDC motor, Multirotor, RC Planets. Specification Model: SIMONK 30A. Constant Current: 30A (Max 40A < 10 sec). BEC: 5V...
Attiny85 Micro-USB module
If you want to embed a microcontroller into a project and are looking for something smaller and cheaper than an Arduino and you don€š¬€ž¢t need a lot of I/O pins or code space, the ATtiny85...
TTP226 - 8 Channel Capacitive Touch Sensor Module
TTP226 - 8 Channel Capacitive Touch Sensor Module having Onboard 8 key TTP226 capacitive touch induction IC and Onboard 8-way level indicator. Capacitive touch allows electronics to detect when your finger is within a few milimeters...
LM2596 DC-DC Buck Converter Adjustable Step Down Module
This is a high-efficiency LM2596 DC-DC step-down converter with a high-precision potentiometer that can drive a load of up to 3A. Please use a heat sink if the output current is larger than 2.5A (or...
1k ohm SMD Resistor 1206 (Pack of 100)
It's a 1k ohm SMD Resistor 1206. The resistor has a low tolerance of only 5%. This SMD Resistor is a conventional thick film chip resistor and is a type of surface-mount resistor. SMD resistors...
330 ohm SMD Resistor 1206 (Reel of 5000)
It's a 330 ohm SMD Resistor 1206. The resistor has a low tolerance of only 5%. This SMD Resistor is a conventional thick film chip resistor and is a type of surface-mount resistor. SMD resistors...
Wheel for BO Motor 70mm x 8mm
It's a 70mm x 8mm Wheel for BO Motor. It diameter is 70mm and width is 8mm. The outer surface are made from rubber and the inner surface material is plastic. Specification Diameter 70 mm Width 8...
LM35 Temperature sensor
It's a LM35 Temperature sensor. This is available in TO-92 package and it's operating voltage rating and current drain is respectively 4 to 30 volt and less than 60mA. Features Analog Output calibrated directly in ° Celsius. ...
BD140 PNP Bipolar Medium Power Transistor (BJT) 80V 1.5A TO-126 Package
The BD140 is a medium power bipolar junction PNP transistor that is mostly utilised in complementary or quasi-complementary circuits in audio amplifiers and drivers. Its mounting style is through hole and the package is To-126....
0.1uF SMD Capacitor 1206 (pack of 100)
This is a 0.1uF 50v SMD Capacitor uses surface mount technology and comes in '1206' packages. This is in small package and it has a good temperature coefficient . This capacitor has a maximum voltage of 50...
XL6009 DC- DC Adjustable Step UP Boost Power Converter Module
This XL6009 Step-up boost converter is a DC-DC Adjustable, non-isolated boost converter that can convert from 3V-32V DC input voltage to an output voltage of 5V-38V DC. This module has high efficiency of up to...
L293D Motor Shield for Arduino
It's a L293D motor shield for Arduino. This type motor driver generally use with Arduino for control the more than one motor. Through this motor driver can drive 4 bidirectional and 2 stepper motor. Specification 2...
28BYJ-48 5V Mini Stepper Motor
The 28BYJ-48 5V Mini Stepper Motor is a compact and reliable motor designed for precise control of rotational movement. Known for its affordability and ease of use, this motor is ideal for automation projects, robotics,...