Sensors
MOC7811 Slotted Opto Isolator Encoder Sensor
MQ4 - Methane (CNG) Natural Gas Sensor Module
10 ohm NTC Thermistor
Light Dependent Resistor 7mm
MAX30102 Pulse Oximeter Heart Rate Sensor Module
Sharp GP2Y10 Optical Dust Sensor
CJMCU 9930 APDS-9930 Digital Proximity And Am...
LM35D Analog Temperature Sensor Module
Micro Load Cell (Weight Sensor) with 5kg Capa...
Micro Load Cell (Weight Sensor) with 3kg Capa...
IR Pulse (Heart Rate) Sensor Module
MQ7 - Carbon Monoxide Gas Sensor Module
5 Ohm 15mm NTC Thermistor
DS18B20 Temperature Sensor Module
MOC7811 Slotted Opto Isolator Encoder Sensor
The MOC7811 is an infrared-based optical sensor. It contains an IR emitter and receiver pair mounted facing each other. It can be used with encoders to detect wheel speed, angle, etc. When the light emitted by...
MQ4 - Methane (CNG) Natural Gas Sensor Module
This MQ4 - Methane Gas sensor module can sense the presence of compressed Natural Gas sensors (CNG), methane(CH4) etc. in the air. This is a very easy to use low-cost semiconductor Gas sensor Module with analog...
10 ohm NTC Thermistor
An NTC thermistor reduces its resistance with an increase in temperature. NTC temperature thermistors have a negative electrical resistance versus temperature (R/T) relationship. The relatively large negative response of an NTC thermistor means that even...
Light Dependent Resistor 7mm
Light Dependent Resistor is a special type of resistor used for the detection of light. As it is a type of resistor hence it doesn€š¬€ž¢t have any polarity and can be connected in any direction....
MAX30102 Pulse Oximeter Heart Rate Sensor Module
MAX30102 is a sensor that combines a pulse oximeter and a heart rate monitor. It's an optical sensor that measures the absorbance of pulsating blood through a photodetector after emitting two wavelengths of light from...
Sharp GP2Y10 Optical Dust Sensor
An infrared emitting diode (IRED) and a phototransistor are diagonally positioned in this PM2.5 GP2Y1010AU0F Dust Smoke Particle Sensor. It detects dust in the air by detecting reflected light. It is especially useful for detecting...
CJMCU 9930 APDS-9930 Digital Proximity And Ambient Light Sensor
This is the CJMCU 9930 APDS-9930 Digital Proximity And Ambient Light Sensor. In a single 8-pin package, the APDS-9930 provides digital ambient light sensing (ALS), an IR LED, and a comprehensive proximity detection system. The...
LM35D Analog Temperature Sensor Module
The LM35D Analog Temperature Sensor Module is a temperature sensor based on the LM35. The LM35 Linear Temperature Sensor module may be used to measure the temperature of the surrounding air. Temperature sensitivity is 10...
Micro Load Cell (Weight Sensor) with 5kg Capacity
This straight bar load cell (also known as a strain gauge) can convert pressure (force) of up to 5kg into an electrical signal. Each load cell can detect variations in electrical resistance that changes in...
Micro Load Cell (Weight Sensor) with 3kg Capacity
This straight bar load cell (also known as a strain gauge) can convert pressure (force) of up to 3kg into an electrical signal. Each load cell can detect variations in electrical resistance that changes in response...
IR Pulse (Heart Rate) Sensor Module
This component is ideally suited for adding heartbeat sensing to your project. This detection module combines a phototransistor and IR LED, which when a finger is placed between will provide a varying signal. Reading this...
MQ7 - Carbon Monoxide Gas Sensor Module
MQ-7 is used for sensing CO concentrations in the air. The MQ-7 can detect CO levels ranging from 10 to 500 parts per million. This sensor has high sensitivity and a fast response time. The...
5 Ohm 15mm NTC Thermistor
An NTC thermistor reduces its resistance with an increase in temperature. NTC temperature thermistors have a negative electrical resistance versus temperature (R/T) relationship. The relatively large negative response of an NTC thermistor means that even...
DS18B20 Temperature Sensor Module
The DS18B20 Digital Thermometer provides 9 to 12-bit (configurable) temperature readings which indicate the temperature of the device.Information is sent to/from the DS18B20 over a 1-Wire interface, so that only one wire (and ground) needs...